Pages: [1] 
|
 |
|
|
Author
|
Topic: G5 Bearing Removal? (Read 1245 times)
|
*SID*
Trade Count:
(38)
The Nation
|
How do you get this thing out? I assume one side of the axle is locktite. I tried pliers, but the bearing isn't budging and the way the axle is designed, I'm affraid I'll bend it.
Anyone able to get it out?
|
|
|
|
|
Logged
|
|
|
|
dunno
Trade Count:
(0)
The Nation
Hello
|
Yeah i got the bearing out just using my fingers. But many peop;e haven't been able to get it out. Maybe try taking the bearing out as straight as possible with your fingers. Or try with plyers. But mine comes out somewhat easily for some reason. Maybe try playing with it because I took it out after playing with the yoyo for bit.
|
|
|
|
|
Logged
|
|
|
|
*SID*
Trade Count:
(38)
The Nation
|
This is rediculous, I can NOT get this thing out.  WD-40, pliers, NOTHING. Anyone got any dynamite? |
|
|
|
|
Logged
|
|
|
|
dunno
Trade Count:
(0)
The Nation
Hello
|
Well just keep trying. I'm not sure how mine came out. One thing I noticed tho is that one the side w/o the axle if I put the bearing on that side the bearing can slide around a tiny bit and when playing the string almost slips on that side too. I think maybe that side the part outside of the bearing is a little too big. Its weird.
|
|
|
|
|
Logged
|
|
|
|
|
|
*SID*
Trade Count:
(38)
The Nation
|
The main bearing that's stuck on the big axle. Not the cap bearings. Thnx though.
|
|
|
|
|
Logged
|
|
|
|
dunno
Trade Count:
(0)
The Nation
Hello
|
Yeah lol, but just keep trying and it should come out with your fingers. Another person i kno couldn't get the bearing out but after some effort it just came.
|
|
|
|
|
Logged
|
|
|
|
*SID*
Trade Count:
(38)
The Nation
|
lol - thnx dunno for letting me vent. I was getting close to hammer time. I just put it away till tomorrow.  |
|
|
|
|
Logged
|
|
|
|
Rockin yo
Jacob
Trade Count:
(0)
The Nation
|
*SID* try finding 2 bolts tht can screw on the axle, and remove the axle ( with the bearing still on) by screwing the 2 bolts on top of each other ( make sure they are tight on top of eachother) and then backing up the bottom bolt. once the axle is out push the bearing off. then u could lightly sand the part where the bearing was mounted so tht it is much easier to remove later hope this helps  |
|
|
|
|
Logged
|
|
|
|
|
|
|
|
*SID*
Trade Count:
(38)
The Nation
|
Thnx dunno, thnx Rockin yo! I finally got this thing out! It's stuck on the axle like it was spot welded. I got it soaking now, so hopefully I can get it off the axle. In any case, I got the silicone going, which was the purpose anyway.  All good. It's a labor of love. |
|
|
|
|
Logged
|
|
|
|
dunno
Trade Count:
(0)
The Nation
Hello
|
Nice job, and with broken in silicone it plays schweeeeet!
|
|
|
|
|
Logged
|
|
|
|
|
Pages: [1] 
|
|
|
 |
